Back to Nature Ultra-Strip.
|
Ultra-Strip
maximum strength paint remover is a
safer, environmentally friendlier paint remover
formulated for maximum stripping action.
|
| |
Ultra-Strip, the ultimate
safe paint remover is utilized for maximum paint stripping action. Ultra-Strip
paste is environmentally friendly, biodegradable, non-flammable, water rinse-able
and contains no methylene chloride, caustic or other harsh chemicals. For
those applications where time of application and removal is critical, a
lighter coat lifts 1 to 4 layers of paint usually in 15 minutes to four
hours. Where multiple layers of paint are indicated, or there are
other more difficult coatings such as two part epoxies and urethanes a heavier
coat will remove the paint in one application. Ultra-Strip maximum strength
paint remover works on a multitude of surfaces including wood, metal, plaster,
masonry, fiberglass, etc. As a non-caustic remover, the surface does not
need to be neutralized. For application, Ultra-Strip maximum strength
paint remover can be brushed, rolled or sprayed.
|
|
|
|
Preparation |
 |
Mask any areas not being stripped
with plastic and masking tape.
|
|
|
If product freezes in bucket,
let thaw and stir vigorously until product is consistent.
|
|
|
Hints |
|
If Ultra-Strip maximum strength
paint remover is applied too thinly, left on too long, or due to
excessive heat conditions, the applied area is difficult to scrape,
try the following:
|
|
|
Mist the applied area with
After Strip, wait 5-15 minutes and remove.
|
|
|
Reapply Ready-Strip over itself,
wait 15 to 30 minutes and remove.
|
|
|
If neither choice above works,
scrape off product and reapply.
|
|
|
|
 Ready
Strip Wash paint remover clean-up is the manufacturers recommended
product for removing residue and softened layers that often remain
after the paint stripping or varnish removal process. It cleans
and prepares the surface for refinishing. This environmentally
safe solution contains no methylene chloride or harsh chemicals,
is non-flammable, non-combustible and biodegradable.
|
|
Ready Strip
Wash 16oz
$9.44
|
Ready Strip
Wash 1-ga
$40.90
|
|
Since it is often
hard to know the type or the amount of paint on a surface, small
test areas should be stripped to determine the proper application
and dwell time needed for paint removal to occur.
(read instructions)
|
|
|
| |
|
|
| |
For stripping 1 to 4 layers of paint quickly
- Apply Ultra-Strip maximum strength paint remover to the surface at a total
of approximately 1/64" thick (10 to 15 mils) with a brush, roller, trowel,
putty knife or sprayer. Can be sprayed effectively using an airless sprayer.
Drill mix before spraying - Remove filters from
sprayer & spray gun. Submerge pump directly into remover. Do
not use suction hose. Use NEW 1/4" or 3/8" airless hose.
Use at least a 1 GPM piston sprayer, .019 - .021 reversible spray tip.
A wet mil gauge should be used to measure thickness. Let the product dwell
from 15 minutes to 4 hours. Follow Suggested Removal Techniques below. Coverage
will vary between 100 and 150 sq. ft. per gallon when this application method
is used. For removal of multiple layers or stubborn coatings -
consult test patch guidelines. Ultra-Strip maximum
strength paint remover will easily cling to vertical surfaces. Use your
tool to fill detailed, intricate or grooved surfaces. For best results apply
at temperatures between 60° F and 80° F. Product activity is reduced below
a temperature of 60° F and may require additional dwell time before all
layers of paint are removed. If product freezes let thaw and stir vigorously
until product is consistent. No Neutralization required. Clean tools promptly
after use with soap and water.
|
|
 |
Friendlier for you ●
Friendlier for your Environment |
|
| |
|
Suggested Removal Techniques
|
|
| |
|
|
| |
Easiest removal is achieved using a 4in
or wider razor blade scraper (commonly known as a wallpaper remover) to
lift the remover/paint off the surface.
|
Easiest removal is achieved using a Back
To Nature Stainless Steel Scraper to strip remover/paint from the surface.
Use a stiff bristle brush with Ready Strip Wash paint remover clean-up paint
remover wash to remove any residue.
|
| |
| Decorative Plaster
or Wood |
|
|
| |
Use a Back To Nature Stainless Steel Scraper
with 5 function detail blade to lift the remover/paint off the surface.
Use a stiff bristle brush with Ready Strip Wash paint remover clean-up to
remove any residue.
|
Use a putty knife to lift the remover/paint
from the surface. Use a stiff bristle brush with Ready Strip Wash paint
remover clean-up to remove any residue remaining.
|
| |
| Masonry, Concrete
Surfaces |
|
|
| |
Remove bulk of remover/paint with a stiff
putty knife or wire brush. Use a wire brush with Ready Strip Wash paint
remover clean-up to remove any residue remaining. Residue can also
be removed with a high pressure washer where permitted.
|
Agitate or rough up remover/paint on the
surface with a wire brush without attempting removal. This helps to lift
bottom layers from the surface. Use a 4in or wider razor blade scraper (wallpaper
remover) or stiff putty knife (pipe railings or irregular surfaces should
use the putty knife) to lift remover/paint off the surface. Use a wire brush
with Ready Strip Wash paint remover clean-up to remove any residue remaining.
|
| |
|
|
| |
Misting the applied area with Ready Strip
Wash paint remover clean-up prior to removal makes lifting of the paint
or varnish easier. Misting with Ready Strip Wash paint remover clean-up
also reactivates the product if it feels dry to the touch. Any paint residue
left on a surface should be removed within a short period of time so that
paint residue will not dry up re-adhere. In some circumstances, it may look
like the last layer of paint is still on the surface. This is not
a dried layer of paint, but paint & remover which has been emulsified so
that it can be removed.
|
Safety goggles are recommended for eye
protection. Protective gloves such as butyl rubber,
neoprene gloves are also recommended. Maintain adequate ventilation
especially in confined areas. If spraying or misting is expected use NIOSH
approved chemical cartridge (organic vapor) respiratory equipment (full
face respirator recommended). In case of inhalation remove victim to fresh
air and provide oxygen if breathing is difficult. In case of eye contact
- flush exposed areas with large quantities of water. In case of skin contact
- wash skin with soap and water. Use emollient skin creams. In case of ingestion
- do not induce vomiting. Call physician immediately.
|
| |
|
to purchase
paint remover or accessories click here
|
|
