RemovALL 320 Architectural paint
remover Brush Grade product label.
|
The Eco-Powerful™ remover
|
|
This powerful paint stripping formula
is engineered to remove graffiti and
most paints including urethane, lacquer, varnish, alkyd and latex paints
from wood, masonry, brick and other porous substrates.
|
Features & Benefits
|
|
Non hazardous Non-toxic Non-Flammable
Low odor Up to 75% more coverage Biodegradable Water based Easy
clean up Reduces labor Reduces down time Reduces pollution
|
SARA Technology
|
|
SARA Technology utilizes physical energy
released by chemical reactions to break the bond between the coating and
the substrate, lifting the paint right off the surface. The paint chips
can be easily removed by vacuuming, scraping or pressure washing.
|
RemovALL™
Tough on Paint Easy on the Environment™
Architectural Paint remover
RemovALL 320
For Wood, Masonry & Brick
Brush Grade
|
|
Preparation:
Cover / protect areas where the paint is to be left on. Remove masking tape
immediately after application as the remover may soak through the tape,
damaging the paint beneath it. Thoroughly mix the remover, prior to use,
with a drill at high speed if available. Do not shake.
Test Patch:
Always prepare a test patch in an inconspicuous area prior to full application.
This will indicate the time required and suitability of product.
Application:
Using a brush, roller or sprayer, apply a thick, even layer onto the area
to be stripped (1.5 mm or better). Brushing and rolling produce lower
film builds, requiring additional applications resulting in longer strip
times. Any spray machine that is suitable for paint applicatoin can be used
to spray RemovALL 320. If using an airless spray machine, use a tip
size of 700 microns (.019in) or larger. Once the remover has been
applied, leave the product alone as agitation slows down penetration.
Coverage:
Yield is approximately 40 to 120 sq. ft. per gallon (1 to 3 sq. m per L).
Re-Application:
If poor adhesion exists between paint layers, the remover may lift the coating
layer by layer. If this happens, remove the lifted layers and re-apply remover.
While the removal process is taking place do not allow the remover to dry
on the surface. If it starts to dry, reapply the remover.
Dwell Time:
The time required for penetration varies according to the types of paint,
the number of layers to be removed and the temperature. Some paint systems
may take between 1 and 6 hours. Leaving the remover overnight will provide
best results.
Removal:
Removal of residue can be completed by scraper, squeegee, wet/dry vacuum
system or by high pressure (2,500 3,500 psi) water wash. Dispose of solid
paint waste in accordance with government regulations.
Temperature:
Above 55°F (13°C). If working in cooler temperatures expect a longer dwell
time. Keep from freezing.
Limited Guarantee / Warranty:
The manufacturers liability under any express or implied guarantee/warranty
is limited solely to replacement of products shown defective or a refund
of the purchase price. Claims must be made within one year of purchase and
be accompanied by proof of purchase. The manufacturer shall not be liable
for injury, cost of labor, or direct, incidental or consequential damages.
|
| In many cases, the coating type
may be unknown. This chart is only a guideline. Always do a
test patch to determine which RemovALL product is best suited for any particular
job. This will also indicate the dwell time required to complete the
project and suitability for the substrate. |
|
Avoid contact
with eyes and skin. Prolonged and repeated exposure to skin may cause irritation.
Wash hands after using. Keep container closed when not in use. Do no transfer
contents to other containers for storage.
CONTAINS:
ALCOHOLS. Use only with adequate ventilation. To avoid over exposure,
open window and doors or use other means to ensure fresh air entry during
application and dwell time. If you experience eye watering, headaches or
dizziness, increase fresh air or wear respiratory protection (NIOSH approved)
or leave the area. Rubber gloves and safety glasses are recommended.
FIRST AID:
In case of eye contact, flush thoroughly with large amounts of water for
15 minutes. If irritation persists, get medical attention. For skin contact,
wash thoroughly with soap and water. In case of respiratory difficulty,
provide fresh air and call physician. If swallowed, get medical attention
immediately.
|
|
DO NOT TAKE INTERNALLY
KEEP OUT OF REACH OF CHILDREN
FOR PROFESSIONAL USE ONLY
SEE MATERIAL SAFETY DATA SHEET
|
| INGREDIENT |
|
C.A.S.# |
| AROMATIC ALCOHOL |
(100-51-6) |
| ALIPHATIC HYDROCARBONS |
(64742-47-8) |
| TRIETHANOLAMINE |
(102-71-6) |
|
