RemovAll 210 Industrial paint
remover product label.
|
The Eco-Powerful™ remover
|
|
This powerful paint stripping formula
is engineered to remove most paints including polyureas, urethane, epoxy,
lacquer, vanish, alkyd and latex paints from steel, aluminum, wood, masonry,
brick and concrete.
|
Features & Benefits
|
|
Non hazardous • Non-toxic • Non-Flammable
• Low odor • Biodegradable • Water based • Easy clean up • Reduces labor
• Reduces pollution
|
SARA Technology
|
|
SARA Technology utilizes physical energy
released by chemical reactions to break the bond between the coating and
the substrate, lifting the paint right off the surface. The paint chips
can be easily removed by vacuum suction, scraping or pressure washing.
|
RemovALL™
Tough on Paint – Easy on the Environment™
Industrial Paint remover
RemovALL 210
For Metal & Concrete
Spray Grade
|
|
Preparation:
Cover / protect areas where the paint is to be left on. Remove masking tape
immediately after application as the remover may soak through the tape,
damaging the paint beneath it. Thoroughly mix the remover, prior to use,
with a high speed drill mixer if available.
Test Patch:
Always prepare a test patch in an inconspicuous area prior to full application.
This will indicate the time required and suitability of product.
Application:
Apply a thick, even layer onto the coating being removed. An airless spray
machine is the most effective means for application. Use a tip size of 700
microns (.019in) or larger. Brushing and rolling produce lower film builds,
requiring additional applications resulting in longer strip times. Once
applied, leave the product alone, as agitation slows down penetration.
Coverage:
The desirable thickness of remover is approximately one and a half times
the dry film thickness of the paint. Minimum thickness should be 15 mils
(wet film). Yield is approximately 40 to 75 sq. ft. per gallon.
Re-Application:
If poor adhesion exists between paint layers, the remover may lift the coating
layer by layer. If this happens, remove the lifted layers and re-apply remover.
While the removal process is taking place do not allow the remover to dry
on the surface. If it starts to dry, reapply the remover.
Dwell Time:
The time required for penetration varies according to the types of paint,
the number of layers to be removed and the temperature. Most paint systems
will take between 1 and 6 hours. Leaving the remover overnight will provide
best results.
Removal:
Removal of residue can be completed by scraper, squeegee, wet/dry vacuum
system or by high pressure (2,500 – 3,500 psi) water wash. Dispose of solid
paint waste in accordance with government regulations.
Temperature:
Above 55°F (13°C). If working in cooler temperatures expect a longer dwell
time. Keep from freezing.
Limited Guarantee / Warranty:
The manufacturers’ liability under any express or implied guarantee/warranty
is limited solely to replacement of products shown defective or a refund
of the purchase price. Claims must be made within one year of purchase and
be accompanied by proof of purchase. The manufacturer shall not be liable
for injury, cost of labor, or direct, incidental or consequential damages.
|
|
RemovALL Product Selection Guide |
| |
Wood |
Concrete |
Brick |
Metal |
Plastic |
| Latex |
310 |
210 |
310 |
210 |
910 |
| Alkyd |
310 |
210 |
310 |
210 |
910 |
| Thick films of
above |
910 |
910 |
910 |
910 |
910 |
|
Zinc Based Coatings |
|
| Inorganic zinc |
|
510 /
210 |
510 /
210 |
510 /
210 |
510 /
210 |
| Organic zinc |
|
510 /
210 |
510 /
210 |
510 /
210 |
510 /
210 |
|
Polyureas - Epoxies |
|
| 100% solids |
110 |
510 |
510 |
510 |
510 |
| Solvented epoxies |
110 |
210 |
210 |
210 |
210 |
| Water based epoxies |
110 |
510 |
510 |
510 |
510 |
|
Urethanes |
|
| Thin film urethanes |
210 |
210 |
310 |
210 |
510 |
| Rigid & elastrometric
urethanes |
310 |
510 /
210 |
310 |
310 |
510 |
|
Graffiti |
|
| Painted, non-porous
surface |
400 |
400 |
400 |
400 |
400 |
| Unpainted, porous
surface |
310 |
310 |
310 |
310 |
310 |
|
Penetrating stains, sealers |
910 |
310 |
310 |
510 /
210 |
|
|
Adhesives & carpet underlay |
700 |
700 |
700 |
700 |
700 |
|
Dip tanks for stripping small parts |
|
|
|
200 |
200 |
|
Paint gun & equipment cleaning |
use RemovALL 300
|
| In many
cases, the coating type may be unknown. This chart is only
a guideline. Always do a test patch to determine which RemovALL
product is best suited for any particular job. This will also
indicate the dwell time required to complete the project and suitability
for the substrate. |
|
|
Avoid contact
with eyes and skin. Prolonged and repeated exposure to skin may cause irritation.
Wash hands after using. Keep container closed when not in use. Do no transfer
contents to other containers for storage.
CONTAINS:
ALCOHOLS. Use only with adequate ventilation. To avoid over exposure,
open window and doors or use other means to ensure fresh air entry during
application and dwell time. If you experience eye watering, headaches or
dizziness, increase fresh air or wear respiratory protection (NIOSH approved)
or leave the area. Rubber gloves and safety glasses are recommended.
FIRST AID:
In case of eye contact, flush thoroughly with large amounts of water for
15 minutes. If irritation persists, get medical attention. For skin contact,
wash thoroughly with soap and water. In case of respiratory difficulty,
provide fresh air and call physician. If swallowed, get medical attention
immediately.
|
| INGREDIENT |
|
C.A.S.# |
| ARYL ALCOHOL |
(100-51-6) |
| PROPYLENE GLYCOL |
(57-55-6) |
| DISTILLATES (PETROLEUM) |
(68477-31-6) |
|
