Oil on concrete driveway? Get
Pour n Restore.
|
Pour-N-Restore Oil Stain Remover
for Concrete & Masonry
|
| Pour-N-Restore
combines the cleaning power of a liquid degreaser
and a dry absorbent into one amazing formula that both dissolves and captures
concrete oil and grease stains. Pour-N-Restore soaks into the concrete,
breaks down oil deep in the pores, and molecularly locks onto oil particles.
As it dries, the oil is pulled up to the surface and absorbed as Pour-N-Restore
begins transforming into powder. When it is completely dry, the oil
is simply swept up for easy disposal. |
|
Important! Test
before using on sealed, colored or painted surfaces. Prior use of other
cleaners may inhibit performance.
For stains
on asphalt or blacktop use Krud Kutter Driveway
Cleaner & Degreaser.
|
|
Pour-N-Restore drying time will be approximately 5 to 8 hours
in temperatures of 60° or more.
Coverage approximately 24 sq ft per gallon. Biodegradable and phosphate
free.
|
V-Notched Spreader
for use with Pour-N-Restore
$ 1.29
Click to Buy
|
Description:
Just
apply, let it dry and sweep it up. Pour-N-Restore combines a powerful
citrus degreaser with a non-leaching absorbent powder to create Micro-Extraction
Technology™. This
Micro-Extraction
Technology™ allows Pour-N-Restore to
soak deep into concrete and masonry surfaces, locking onto embedded oil-based
stains at a molecular level. As Pour-N-Restore® dries to a powder,
the stain is extracted to the surface and absorbed for easy cleanup.
Stains Removed:
Pour-N-Restore
will remove stains from motor oil, grease, hydraulic fluid, anti-freeze,
brake fluid, transmission fluid, synthetic oils, food grease from animal
fats, cooking oil, tar, citronella oil and wax.
Surfaces:
Pour-N-Restore
can be used on various concrete and masonry surfaces including exposed aggregate,
patio blocks, paving bricks, quarry tile, stone and colored concrete.
Do not use on asphalt or blacktop. For asphalt or blacktop
stains use Krud Kutter Driveway Cleaner & Degreaser.
|
|
1-ga
Pour-N-Restore
0.31 per oz
$ 39.96
Click to Buy
|
|
16oz
Pour-N-Restore
0.47 per oz
$ 7.56
Click to Buy
|
32oz
Pour-N-Restore
0.37 per oz
$ 11.88
Click to Buy
|
2.5 gallon
Pour-N-Restore
0.29 per oz
$ 93.96
Click to Buy
|
55 gallon
Pour-N-Restore
0.26 per oz
$ 1,819.80
Click to Buy
|
|
Product Note!
Due to shipper
license requirements on flammability we are unable to offer Pour-N-Restore
for shipment
to any area outside the Continental
United States.
|
|
Sample application of Pour-N-Restore
|
|
Step 1:
Before using Pour-N-Restore you should remove any
heavy buildup of tar, oil, grease etc. from the surface.
Pour-N-Restore works by soaking into the surface pores where its Micro-Extraction
Technology captures stains at the molecular level. Removing heavy
buildup prior to use will greatly increase the effectiveness of the product.
|
Step 2:
After removal of stain build up,
Read the
product label thoroughly.
Apply Pour-N-Restore directly to the stained area.
Put a moderate amount of the product on the surface, keeping in mind that
the faster Pour-N-Restore dries the more effective it will be.
|
|
|
|
|
Prior Treatment:
In cases where stains have been treated previously with another product,
Pour-N-Restore may not be as effective because it cannot remove the dirt
and other materials without the presence of oil. Pour-N-Restore is designed
to lock onto oil molecules and draw them up to the surface through the process
of evaporation. Dirt and other foreign materials are removed through this
process because they are mixed in with the oil.
|
|
The cleaning
power of Citrus
No scrubbing, no rinsing, no mess
Pour-N-Restore Oil Stain Remover
for Concrete & Masonry
|
|
|
Step 3:
Let the product DRY.
Several factors affect dry time including temperature, humidity,
and ventilation. The ideal environment would be well ventilated (outside),
low in humidity, and high in temperature (over 70'F). In this ideal environment
dry time may only be a few hours. The least ideal environment would be poorly
ventilated (enclosed room), high in humidity, and low in temperature (below
60'F). In this environment, it could take several days for Pour-N-Restore
to dry completely.
|
Step 4:
Sweep up the absorbent powder and discard.
Concrete may still appear dark immediately after Pour-N-Restore is swept
up. This is generally not oil, but moisture from Pour-N-Restore still trapped
in the pores. Simply provide adequate ventilation and allow the moisture
to evaporate. This could take anywhere from 15 minutes to 1 week depending
on the environment. However if the product was still wet when swept
up; or applied to thinly (see V-Notched spreader below); you may
require a second application.
|
|
|
|
|
|
V-Notched Spreader
 Tips
for product application:
For best results with Pour-N-Restore Oil Stain Remover,
use the ¼ inch edge of a V-notch trowel spreader. This will allow you to
maximize coverage and accelerate the dry time of Pour-N-Restore Oil Stain
Remover. It is ideal for use in climates that experience cooler weather
or high humidity. To purchase the V-Notched trowel Spreader
click here.
Tips for use in cold, humid, or poorly ventilated areas:
To accelerate dry time, spread Pour-N-Restore to leave a thinner coating.
This will allow for faster evaporation but will also reduce absorption capacity,
thereby necessitating additional applications. Another recommendation is
to apply a fan directly to the treated area to maximize ventilation.
This will accelerate evaporation considerably. A final recommendation is
to simply sweep Pour-N-Restore off the stained area after 8 hours, even
if it is not completely dry. We have found that Pour-N-Restore is still
quite effective in these situations because it has been allowed ample time
to remove most of the oil from the concrete.
|
Scrubbing:
We never recommend scrubbing Pour-N-Restore on the first application because
this can actually hinder performance. However, since agitation can help
break dirt and other debris loose, scrubbing may improve performance on
subsequent applications in cases where oil content is low.
Age of stain:
The generally is not a factor. Rather, it is the amount of oil in the
stain that makes a difference. As stated earlier, oil must be present in
order for Pour-N-Restore to effectively remove the stain, A 10 year old
stain that had oil deposited onto it continuously will be much easier to
remove than a 1 year old stain that never had oil deposited onto it after
the initial occurrence. The manufacturer suggests receiving feedback from
customers that used Pour-N-Restore to effectively remove oil stains that
were 1 - 30 years old. In these instances more than one application may
have been required.
Sealants:
Pour-N-Restore can soak through tiny holes in sealants. In such cases, sealants
may trap moisture in the concrete, preventing proper evaporation. In one
instance, it took over 4 weeks for the moisture to evaporate completely.
However, there are other cases where sealants did not pose a problem. If
your concrete surface has been sealed, test product in an inconspicuous
area first to determine results.
|
|
Do not use on asphalt or blacktop.
For
asphalt or blacktop stains use Krud Kutter Driveway
Cleaner & Degreaser. |
|
