Multi-Strip heavy duty paint remover.
|
Multi-Strip
heavy duty paint
remover can remove more difficult coatings
such as two part epoxy, urethanes and is also effective
on mastic, adhesives, and glues...
|
| |
Multi-Strip heavy duty paint
remover is a unique, environmentally safe paint remover designed to remove
up to 15 layers of paint in one application. While other paint removers
evaporate in a short time and lose their strength, the longer you leave
on Multi-Strip heavy duty paint remover the more layers of paint it removes.
It is biodegradable, non-flammable, non-combustible and contains no methylene
chloride or caustic. Multi-Strip heavy duty paint remover is odor-free and
can be easily cleaned up with Ready Strip Wash paint remover clean-up. As
a paste it clings easily to vertical surfaces and completely fills detailed
areas. For application, it can be brushed, rolled or sprayed on the surface
with an airless paint sprayer. In addition, it creates less waste for easy
disposal. It requires no neutralization (neutral pH).
|
|
|
|
Preparation |
 |
Mask any areas not being stripped
with plastic and masking tape.
|
|
|
If product freezes in bucket,
let thaw and stir vigorously until product is consistent.
|
|
|
Hints |
|
If Multi-Strip heavy duty paint
remover is applied too thinly, left on too long, or due to excessive
heat conditions, the applied area is difficult to scrape, try the
following:
|
|
|
Misting the applied area with
Ready Strip Wash paint remover clean-up prior to removal makes
lifting of the paint or varnish easier.
|
|
|
Misting with Ready Strip Wash
paint remover clean-up also reactivates the product if it feels
dry to the touch.
|
|
|
Any residue left on a surface
should be removed within a short period of time so that paint
residue will not dry up and re-adhere to the surface.
|
|
|
|
 Ready
Strip Wash paint remover clean-up is the manufacturers recommended
product for removing residue and softened layers that often remain
after the paint stripping or varnish removal process. It cleans
and prepares the surface for refinishing. This environmentally
safe solution contains no methylene chloride or harsh chemicals,
is non-flammable, non-combustible and biodegradable.
|
|
Ready Strip
Wash 16oz
$9.44
|
Ready Strip
Wash 1-ga
$40.90
|
|
Since it is often
hard to know the type or the amount of paint on a surface, two small
test areas should be stripped to determine the proper application
and dwell time needed for paint removal to occur.
(read instructions)
|
|
|
| |
|
|
| |
Multi-Strip heavy duty paint remover is
applied to the surface at a total of approximately 1/32" thick (30 mils)
with a brush, roller, putty knife or sprayer. Can be sprayed effectively
using an airless sprayer. Drill mix before spraying
- Remove filters from sprayer & spray gun - Submerge pump directly into
remover. Do not use suction hose - Use NEW 1/4" or 3/8" airless hose.
Use at least a 1 GPM piston sprayer, .019-.021 reversible spray tip. A wet
mil gauge should be used to measure thickness. Multi Strip heavy duty
paint remover will easily cling to vertical surfaces. Use your tool to fill
detailed, intricate or grooved surfaces. For best results apply Multi-Strip
heavy duty paint remover at temperatures between 60° F and 80° F. Product
activity is reduced below a temperature of 60° F and may require additional
dwell time before all layers of paint are removed. If product freezes let
thaw and stir vigorously until product is consistent. Coverage for Multi-Strip
heavy duty paint remover varies between 50 and 75+ sq. ft. per gal. depending
upon the type and amount of paint on a surface. No Neutralization required.
Clean tools promptly after use with soap and water.
|
|
|
Multi-Strip - Performance Information
|
|
Our test
boards had 15 painted layers.
|
What's on the
boards?
2 layers latex primer (white)
2 layers oil base Rust Oleum (pink)
2 layers latex (blue)
2 layers latex (yellow)
1 layer latex Krylon (purple)
2 layers oil base Rust Oleum (pink)
2 layers latex (dark blue)
2 layers latex (white)
Observations
during use:
We applied Multi-Strip to our test board in a temperature controlled environment.
The product had a very spreadable consistency with little to no odor.
Recommendations
for Multi-Strip:
At 24 hours we used the ProGrip2 putty knife to easily remove 13 of the
15 painted layers. This product performed equally the same as Strip
Tox except that it is not designed for lead based paint and its consistency
is much looser whereas Strip Tox is more paste-like. If you are not
stripping lead based paint and do not have many vertical surfaces to strip
then Multi-Strip would be a better buy at $25.00 savings per gallon.
|
 |
Friendlier for you ●
Friendlier for your Environment |
|
| |
|
Suggested Removal Techniques
|
|
| |
|
|
| |
Easiest removal is achieved using a 4in
or wider razor blade scraper (commonly known as a wallpaper remover) to
lift the remover/paint off the surface.
|
Easiest removal is achieved using a Back
To Nature
stainless steel scraper to strip remover/paint from
the surface. Use a stiff bristle brush with Ready Strip Wash paint remover
clean-up to remove any residue.
|
| |
| Decorative Plaster
or Wood |
|
|
| |
Use a Back To Nature Stainless Steel Scraper
with 5 function detail blade to lift the paint off the surface. Use a stiff
bristle brush with Ready Strip Wash paint remover clean-up to remove any
residue.
|
In some cases, it may look like the last
layer of paint is still on the surface. This is not a dried layer, but paint
which has been emulsified so it can be removed.
|
| |
| Masonry, Concrete
Surfaces |
|
|
| |
Remove bulk of remover/paint with a stiff
putty knife or wire brush. Use a wire brush with Ready Strip Wash paint
remover clean-up to remove any residue remaining. Residue can also be removed
with a high pressure washer where permitted.
|
Agitate or rough up remover/paint on the
surface with a wire brush without attempting removal. This helps to lift
bottom layers from the surface. Use a 4in or wider razor blade scraper (wallpaper
remover) or stiff putty knife (pipe railings or irregular surfaces should
use the putty knife) to lift remover/paint off the surface. Use a wire brush
with Ready Strip Wash paint remover clean-up to remove any residue.
|
|
|
|
Safety goggles are recommended for eye
protection. Wear protective gloves such as butyl rubber,
neoprene. Maintain adequate ventilation especially in confined areas.
If spraying or misting is expected use NIOSH approved chemical cartridge
(organic vapor) respiratory equipment (full face respirator recommended.
In case of inhalation - remove victim to fresh air and provide oxygen if
breathing is difficult. In case of eye contact - flush exposed areas with
large quantities of water. In case of skin contact - wash skin with soap
and water. Use emollient skin creams. In case of ingestion - do not induce
vomiting. Call physician immediately.
|
| |
|
to purchase
paint remover or accessories click here
|
|
